<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META HTTP-EQUIV="Content-Type" CONTENT="text/html; charset=us-ascii">
<TITLE>Message</TITLE>
<META content="MSHTML 6.00.2800.1400" name=GENERATOR></HEAD>
<BODY>
<DIV><FONT face=Arial><SPAN class=546494320-10062004>Glen:</SPAN></FONT></DIV>
<DIV><FONT face=Arial><SPAN class=546494320-10062004>Yes, I did use
insert-ethers. It did not get that far for the frontend to detect the MAC
address. I have successfully added five compute nodes before (older
motherboard). The installation on these new machines is terminated right after
trying to run anaconda. Some linux discussion group suggests that this might be
due to the fact that Redhat7.3 does not work well with the newer
motherboard/hardware. Is there any workaround you recommend? I would prefer to
leave the frontend as is (Biobrew0.9) since the Blast works very well with SGE.
Thanks.</SPAN></FONT></DIV>
<DIV><FONT face=Arial><SPAN class=546494320-10062004>Heming</SPAN></FONT></DIV>
<DIV><FONT face=Arial><SPAN class=546494320-10062004></SPAN></FONT> </DIV>
<DIV><FONT face=Arial><SPAN class=546494320-10062004>></SPAN>Did you run
'insert-ethers' on the frontend? If so, did you see a MAC=20<BR><SPAN
class=546494320-10062004>></SPAN>address in the insert-ethers window? Are you
sure about which interface=20=<BR><BR><SPAN
class=546494320-10062004>></SPAN>is eth0 on the new nodes and the
frontend? Can you try to install one=20=<BR><BR><SPAN
class=546494320-10062004>></SPAN>of the nodes with a crossover cable attached
to eth0 on the frontend?<BR><BR><SPAN
class=546494320-10062004>></SPAN>Glen<BR><BR><SPAN
class=546494320-10062004>></SPAN>On Jun 10, 2004, at 12:46 PM, Xing,Heming
wrote:<BR></DIV></FONT>
<DIV><FONT face=Arial><EM><SPAN class=546494320-10062004>>></SPAN>Hi
everyone:<BR> <BR><SPAN class=546494320-10062004>>></SPAN>I installed
a BioBrew0.9 cluster with 5 compute nodes half a year ago.<BR><SPAN
class=546494320-10062004>></SPAN>Recently, I got three more machines I want
to add to the cluster. They are<BR><SPAN
class=546494320-10062004>>></SPAN>Intel Desktop Board D865GBF/D865GLC
based P4 with 1 GB RAM. When I tried to<BR><SPAN
class=546494320-10062004>></SPAN>install from PXE or from CD-ROM, I got the
error message says:" install<BR><SPAN
class=546494320-10062004>>></SPAN>exited abnormally-received signal 11."
Then it send termination signals and<BR><SPAN
class=546494320-10062004>>></SPAN>informs me that I can safely reboot. I
also tried BioBrew1.0 the same error<BR><SPAN
class=546494320-10062004>>></SPAN>message comes up. Do you guys have any
suggestions? Or do you know what<BR><SPAN
class=546494320-10062004>>></SPAN>could be the cause of the problem?
<BR><SPAN class=546494320-10062004>>></SPAN>Thanks.<BR><SPAN
class=546494320-10062004>>></SPAN>Heming</EM><BR><BR></FONT></DIV></BODY></HTML>